2024 BMW i7 Stock Height with 22×9 Niche Prodigy 5 & 255/35R22 / 295/30R22 Tires

2024 BMW i7 Wheel and Tire Setup

This 2024 BMW i7 runs a staggered set of Niche Prodigy 5 wheels finished in Silver With Machined Face, with a 22×9 front wheel and a 22×10.5 rear wheel wrapped in 255/35R22 front and 295/30R22 rear tires. The suspension remains at factory ride height, making the wheel and tire package responsible for the change in stance.

The deep concave Prodigy 5 design suits the long G70 body, and Silver With Machined Face contrasts cleanly against darker paint while echoing the bright grille surround.

Factory vs New Specs

A common factory setup on the 2024 BMW i7 uses a staggered 20×9 front wheel with a 255/45R20 tire and a 20×10.5 rear wheel with a 285/40R20 tire, both measuring approximately 29.0 inches tall.

Factory Wheel: Approximately 20×9 front and 20×10.5 rear on the common staggered package.

Factory Tire: 255/45R20 front measuring approximately 29.04 inches tall, and 285/40R20 rear measuring approximately 28.98 inches tall.

New Wheel: 22×9 Niche Prodigy 5 front and 22×10.5 Niche Prodigy 5 rear.

New Wheel Offset: +22mm front and +38mm rear.

New Tire: 255/35R22 front measuring approximately 29.03 inches tall, and 295/30R22 rear measuring approximately 28.97 inches tall.

Wheel Diameter: The wheel increases by 2 inches on both axles, from 20 inches to 22 inches.

Wheel Width: Front width stays at approximately 9 inches. Rear width stays at approximately 10.5 inches.

Tire Width: Front nominal tire width stays at 255mm. Rear nominal tire width increases from 285mm to 295mm.

Tire Diameter and Ground Clearance

The factory front 255/45R20 measures approximately 29.04 inches tall, while the 255/35R22 measures approximately 29.03 inches.

That is a difference of only about 0.01 inch in overall front diameter. Static ground clearance at the front axle is effectively unchanged.

At the rear, the factory 285/40R20 measures approximately 28.98 inches, while the 295/30R22 measures approximately 28.97 inches. That is about 0.01 inch difference overall, or effectively no meaningful change in static clearance.

Keeping rolling diameter this close to factory matters on an EV, where range estimates track circumference. Speedometer difference is negligible at approximately 0.0 percent using the front diameters as the reference.

Offset and Wheel Position

The Niche Prodigy 5 package for this application uses a 22×9 front wheel at +22mm and a 22×10.5 rear wheel at +38mm. Compared with a factory-style 20×9 +24 front and 20×10.5 +44 rear setup, the widths stay the same while front offset drops 2mm and rear offset drops 6mm.

Up front, the outer edge sits approximately 2mm, or about 0.08 inch, farther outward than the factory front wheel — essentially unchanged for everyday appearance.

At the rear, the outer edge sits approximately 6mm, or about 0.24 inch, farther out, while the inner edge gains about 6mm of clearance. The staggered Prodigy 5 package stays near flush at both ends at stock height.

Fitment and Stance

Holding the factory staggered widths while stepping from 20 to 22 inches shortens the sidewall and puts more machined Prodigy 5 face in the arch without changing the front-to-rear width balance.

Fitment Notes

Suspension: This build remains at factory ride height with no lift or lowering kit required for the appearance shown here.

Tire Size: 255/35R22 front and 295/30R22 rear keep overall diameters aligned with the factory 255/45R20 and 285/40R20 package on 22×9 and 22×10.5 wheels.

Rubbing: The gallery fitment notes list no rubbing for this build. Final clearance should still be checked through full steering lock and suspension compression during installation.

Poke: Front +22mm and rear +38mm keep the Prodigy 5 package near flush, with only about 2mm more front poke and 6mm more rear poke than the factory reference wheels.

Inner Clearance: Widths match the common factory 20 inch package, so inner position changes come from offset alone and remain small at both axles.

Center Bore: The Fitment Dynamics Prodigy 5 variants for this 5×112 package use a 72.6mm center bore, larger than the i7’s 66.6mm hub, so the proper hub-centric rings should be used during installation.

Wheel Load Rating: The cataloged variant lists a 1,800 pound load rating per wheel. Tire load capacity should also be verified for the vehicle.

Ride and Drivability

The biggest drivability change comes from the reduced tire sidewall. Moving from 45- and 40-series factory tires to 35- and 30-series 22 inch tires shortens the rubber between the wheel and the road, so sharper impacts will be more noticeable.

At the same time, keeping overall tire diameters nearly identical to factory helps preserve ride height, speedometer accuracy and EV range estimates.

Stock Suspension

The BMW i7 uses two-axle air suspension with adaptive dampers as part of its factory chassis package. Exact calibration can vary by options, but the hardware remains the factory air system when the car is described as stock height.

For gallery fitment purposes, the important detail is that this build maintains factory ride height without a lift or lowering kit.

Fitment Dynamics Miami

Fitment Dynamics carries wheels, tires and suspension upgrades for BMW i7 applications, including Niche wheel and tire packages in 20 and 22 inch fitments. Our team can help determine the proper wheel width, offset and tire size while accounting for fender clearance, suspension clearance, load capacity and everyday drivability.

Customers can visit Fitment Dynamics in the Miami area for professional wheel and tire installation, fitment assistance and local pickup, or have their wheel and tire package shipped nationwide directly to their door.

Fitment Dynamics
8224 NW South River Dr
Medley, FL 33166
786-244-5565