2019 Dodge Charger Hellcat Stock Height with 22×9 / 22×10.5 Niche Prodigy 5 & 245/35R22 / 285/30R22 Tires
Wheel Specs:
Niche Prodigy 5 22×9 Offset: 15
Rear Wheel Specs:
22×
10.5
Offset: 18
Tire Specs:
Front Size: 245/35R22
Rear Size: 285/30R22
Wheel & Tire Fitment Notes
Flush
No Rubbing
No Trimming
Suspension:
Stock Height
2019 Dodge Charger Hellcat Wheel and Tire Setup
This 2019 Dodge Charger Hellcat runs a staggered set of Niche Prodigy 5 wheels finished in matte black, with a 22×9 front wheel and a 22×10.5 rear wheel wrapped in 245/35R22 front and 285/30R22 rear tires. The suspension remains at factory ride height per the gallery notes, making the wheel and tire package the main change in stance on this LD Hellcat.
The split five-spoke Prodigy 5 design suits the Charger’s long rear quarter especially well because the deeper rear concave face fills the opening without looking thin against the wide hip. The matte black finish keeps the package blacked-out against the silver bodywork and black hood, and lets the red front Brembo calipers show through the spokes on Miami streets and garage floors.
Factory vs New Specs
A common factory setup on the standard-body 2019 Dodge Charger Hellcat uses a square 20×9.5 wheel with a +18.5mm offset and a 275/40R20 tire. Widebody Hellcats used a staggered 20×9.5 / 20×11 package with wider rear tires, so exact factory hardware can vary by body style.
Factory Wheel: Approximately 20×9.5 +18.5 on the common standard-body layout.
Factory Tire: 275/40R20, measuring approximately 28.66 inches tall.
New Wheel: 22×9 Niche Prodigy 5 front and 22×10.5 Niche Prodigy 5 rear.
New Wheel Offset: +15mm front and +18mm rear.
New Tire: 245/35R22 front measuring approximately 28.75 inches tall, and 285/30R22 rear measuring approximately 28.73 inches tall.
Wheel Diameter: The wheel increases by 2 inches on both axles, from 20 inches to 22 inches.
Wheel Width: Front width decreases slightly from approximately 9.5 inches to 9 inches. Rear width increases from approximately 9.5 inches to 10.5 inches versus the square factory reference.
Tire Width: Front nominal tire width decreases from 275mm to 245mm. Rear nominal tire width increases from 275mm on the square factory tire to 285mm.
Tire Diameter and Ground Clearance
The factory 275/40R20 measures approximately 28.66 inches tall, while the 245/35R22 measures approximately 28.75 inches.
That is a difference of only about 0.09 inch in overall front diameter, or roughly 0.3 percent. Static ground clearance at the front axle increases by about 0.05 inch from the tire itself.
At the rear, the 285/30R22 measures approximately 28.73 inches, about 0.07 inch taller than the square factory 275/40R20 reference, or about 0.04 inch more static clearance at the rear axle.
Speedometer difference remains negligible. Using the front diameters as the reference, actual road speed is approximately 0.3 percent higher than the indicated speed.
Offset and Wheel Position
The Niche Prodigy 5 package for this application uses a 22×9 front wheel at +15mm and a 22×10.5 rear wheel at +18mm. Compared with a factory-style 20×9.5 +18.5 standard-body wheel, the front loses 0.5 inches of width with 3.5mm less positive offset, and the rear gains 1 inch of width with 0.5mm less positive offset.
Up front, the outer edge sits approximately 3mm, or about 0.11 inch, farther inward than the factory front wheel, while the inner edge gains about 10mm of clearance toward the suspension.
At the rear, the outer edge sits approximately 13mm, or about 0.52 inch, farther out, and the inner edge moves about 12mm, or roughly 0.48 inch, closer to the suspension. The net result is a flush staggered stance that puts more matte Prodigy 5 face in the rear opening while keeping the front near the factory track.
Fitment and Stance
Keeping a staggered layout follows the way wide-hip Chargers look best. The extra two inches of diameter, the slightly narrower front barrel and the much wider rear wheel put more matte black Prodigy 5 face in the arches without converting the car to a square setup.
The 245 front and 285 rear tires keep section width matched to the 9 and 10.5 inch barrels, so the package reads aggressive without looking over-stretched on either axle.
At the ride height shown in the gallery, the 22 inch wheels close up the arch gap that smaller factory packages leave on these Hellcats while the staggered rear still prioritizes the wide-hip look the chassis was built around.
Fitment Notes
Suspension: Gallery notes list this build at factory ride height with no lift required for the wheel and tire package shown here. Final ride-height hardware should still be confirmed on the vehicle during installation.
Tire Size: 245/35R22 front and 285/30R22 rear are commonly paired with 22×9 and 22×10.5 wheels on the LD Charger and keep overall diameters extremely close to the factory 20 inch Hellcat tire.
Rubbing: The gallery fitment notes list no rubbing and no trimming for this build. Final clearance should still be checked through full steering lock and suspension compression during installation, especially with the wider rear package and the Hellcat’s large Brembo brakes.
Poke: Front +15mm and rear +18mm keep the staggered Prodigy 5 package near flush, with the front slightly more tucked than the factory reference and about 13mm more rear poke than the square 20×9.5 factory wheel.
Inner Clearance: Front inner clearance improves versus the factory reference, while the rear inner edge moves about 12mm closer to the suspension and should be checked at full compression.
Center Bore: The Niche Prodigy 5 in 5×115 uses a 72.56mm center bore, larger than the Hellcat’s approximately 71.5mm hub, so the proper hub-centric rings should be used during installation.
Wheel Load Rating: The cataloged 22 inch Prodigy 5 variants for this package list an 1,800 pound load rating per wheel. Tire load capacity should also be verified for the vehicle.
Ride and Drivability
The biggest drivability change comes from the reduced tire sidewall. Moving from a 40-series factory tire to 35-series front and 30-series rear 22 inch tires shortens the rubber between the wheel and the road, so sharper impacts will be more noticeable on Miami streets and highway expansion joints.
At the same time, keeping overall tire diameters extremely close to the common 20 inch Hellcat package helps preserve gearing, ride height and speedometer accuracy.
The wider 285 rear footprint also puts more rubber on the ground than the original square 275 factory tire without jumping to an extreme track-only rear width.
Stock Suspension
The 2019 Dodge Charger Hellcat uses a short- and long-arm front suspension and a five-link independent rear suspension with Bilstein adaptive dampers. Exact spring and damper hardware can vary even when ride height remains stock.
For gallery fitment purposes, the important detail is that this build is documented at factory ride height and does not rely on a lift modification to accommodate the 22 inch staggered wheel and tire package.
Fitment Dynamics Miami
Fitment Dynamics carries wheels, tires and suspension upgrades for Dodge Charger applications, including Niche wheel and tire packages in 18, 20, 22 and 24 inch fitments. Our team can help determine the proper wheel width, offset and tire size while accounting for fender clearance, suspension clearance, load capacity and everyday drivability.
Customers can visit Fitment Dynamics in the Miami area for professional wheel and tire installation, fitment assistance and local pickup, or have their wheel and tire package shipped nationwide directly to their door.
Fitment Dynamics
8224 NW South River Dr
Medley, FL 33166
786-244-5565






