2020 Toyota Supra Stock Height with 20×9 Niche Calabria 5 & 255/30R20 / 285/30R20 Tires
Wheel Specs:
Niche Calabria 5 20×9 Offset: 27
Rear Wheel Specs:
20×
10.5
Offset: 38
Tire Specs:
Front Size: 255/30R20
Rear Size: 285/30R20
Wheel & Tire Fitment Notes
Flush
No Rubbing
No Trimming
Suspension:
Stock Height
2020 Toyota Supra Wheel and Tire Setup
This 2020 Toyota Supra runs a staggered set of Niche Calabria 5 wheels finished in Matte Gunmetal, with a 20×9 front wheel and a 20×10.5 rear wheel wrapped in 255/30R20 front and 285/30R20 rear tires. The suspension remains at factory ride height, making the wheel and tire package responsible for the change in stance.
The split five-spoke Calabria 5 design suits the A90’s wide rear arches, and Matte Gunmetal stays visually quiet against darker bodywork while still showing the mesh detail.
Factory vs New Specs
A common factory setup on the 2020 Toyota Supra 3.0 uses a staggered 19×9 front wheel with a 255/35R19 tire and a 19×10 rear wheel with a 275/35R19 tire.
Factory Wheel: Approximately 19×9 front and 19×10 rear on the common 3.0 package.
Factory Tire: 255/35R19 front measuring approximately 26.03 inches tall, and 275/35R19 rear measuring approximately 26.58 inches tall.
New Wheel: 20×9 Niche Calabria 5 front and 20×10.5 Niche Calabria 5 rear.
New Wheel Offset: +27mm front and +38mm rear.
New Tire: 255/30R20 front measuring approximately 26.02 inches tall, and 285/30R20 rear measuring approximately 26.73 inches tall.
Wheel Diameter: The wheel increases by 1 inch on both axles, from 19 inches to 20 inches.
Wheel Width: Front width stays at approximately 9 inches. Rear width increases from approximately 10 inches to 10.5 inches.
Tire Width: Front nominal tire width stays at 255mm. Rear nominal tire width increases from 275mm to 285mm.
Tire Diameter and Ground Clearance
The factory front 255/35R19 measures approximately 26.03 inches tall, while the 255/30R20 measures approximately 26.02 inches.
That is a difference of only about 0.00 inch in overall front diameter. Static ground clearance at the front axle is effectively unchanged.
At the rear, the factory 275/35R19 measures approximately 26.58 inches, while the 285/30R20 measures approximately 26.73 inches. That is about 0.15 inch taller overall, or about 0.08 inch more static clearance at the rear axle.
Speedometer difference remains small. Using the front diameters as the reference, actual road speed is approximately 0.0 percent different from the indicated speed.
Offset and Wheel Position
The Niche Calabria 5 package for this application uses a 20×9 front wheel at +27mm and a 20×10.5 rear wheel at +38mm. Compared with a factory-style 19×9 +32 front and 19×10 +40 rear setup, the front width stays the same while offset drops 5mm, and the rear gains 0.5 inches of width with 2mm less positive offset.
Up front, the outer edge sits approximately 5mm, or about 0.20 inch, farther outward than the factory front wheel, while the inner edge gains about 5mm of clearance toward the suspension.
At the rear, the outer edge sits approximately 8mm, or about 0.33 inch, farther out, and the inner edge moves about 4mm closer to the suspension. The net result is a flush staggered stance at stock height.
Fitment and Stance
Keeping a staggered layout follows the way the A90 was designed. The extra inch of diameter and the slightly wider rear wheel put more Calabria 5 face in the opening without converting the car to a square setup.
Fitment Notes
Suspension: This build remains at factory ride height with no lift or lowering kit required for the appearance shown here.
Tire Size: 255/30R20 front and 285/30R20 rear are commonly paired with 20×9 and 20×10.5 wheels on the A90 and keep overall diameters close to the factory 19 inch tires.
Rubbing: The gallery fitment notes list no rubbing for this build. Final clearance should still be checked through full steering lock and suspension compression during installation.
Poke: Front +27mm and rear +38mm keep the staggered Calabria 5 package near flush, with only about 5mm more front poke and 8mm more rear poke than the factory reference wheels.
Inner Clearance: Front inner clearance improves slightly versus stock, while the rear inner edge moves about 4mm closer to the suspension and should be checked at full compression.
Center Bore: The Fitment Dynamics Calabria 5 5×112 variants for this package use a 66.7mm center bore, matching the Supra hub.
Wheel Load Rating: The cataloged variant lists a 1,800 pound load rating per wheel. Tire load capacity should also be verified for the vehicle.
Ride and Drivability
The biggest drivability change comes from the reduced tire sidewall. Moving from 35-series factory tires to 30-series 20 inch tires shortens the rubber between the wheel and the road, so sharper impacts will be more noticeable.
At the same time, keeping overall tire diameters nearly identical to factory helps preserve gearing, ride height and speedometer accuracy.
Stock Suspension
The 2020 Toyota Supra uses a MacPherson strut front suspension and a multi-link rear suspension. Adaptive variable suspension was widely fitted on 3.0 models, so damper hardware can vary by package even when ride height remains stock.
For gallery fitment purposes, the important detail is that this build maintains factory ride height without a lift or lowering kit.
Fitment Dynamics Miami
Fitment Dynamics carries wheels, tires and suspension upgrades for Toyota Supra applications, including Niche wheel and tire packages in 19, 20 and 22 inch fitments. Our team can help determine the proper wheel width, offset and tire size while accounting for fender clearance, suspension clearance, load capacity and everyday drivability.
Customers can visit Fitment Dynamics in the Miami area for professional wheel and tire installation, fitment assistance and local pickup, or have their wheel and tire package shipped nationwide directly to their door.
Fitment Dynamics
8224 NW South River Dr
Medley, FL 33166
786-244-5565






